|
Product Details:
|
| Material: | Q235 Steel, Hot Dip Galvanized | Coating: | 275g/m2 Zinc |
|---|---|---|---|
| Thickness: | 1.0mm-1.2mm | Band Width: | 28mm |
| Diameter Range: | 80mm-600mm | Seal: | UV Stabilised EPDM |
| Locking Type: | Over-centre Toggle Handle | Application: | Outdoor Ventilation, Container Houses, Site Ducting |
| Highlight: | Hot dip galvanized duct clamp,Outdoor duct coupling clamp,275g zinc coating clamp |
||
Outdoor ductwork fails at the joint long before the duct itself does. This duct coupling clamp is therefore electro-cleaned and hot dip galvanized after pressing, so the zinc covers the cut edges and the inside of the rolled channel as well as the flat face. The coating is controlled at 275g per square metre, which is the level normally specified for plant installed on roofs, container houses and construction site ventilation where rain, condensate and airborne salt are present every day.
The clamp joins two lengths of round duct or connects duct to a flexible hose, and it is closed by a single over-centre toggle. A UV stabilised EPDM ring sits in the channel and compresses against the duct wall, so the joint stays sealed through thermal cycling from cold nights to sun heated afternoons without the seal hardening and cracking. Because the diameter is continuously adjustable from 80mm to 600mm, a service van can carry one clamp family and still cover most of the ducts found on an outdoor installation.
Site teams often order a hot dip galvanized duct clamp when the duct run leaves the building, because a painted fitting will not survive a winter on a roof. An outdoor duct coupling clamp from this range is coated after pressing, and the 275g zinc coating clamp specification matches what most mechanical consultants ask for on external ductwork.
| Product Type | Duct coupling clamp with over-centre toggle |
|---|---|
| Base Material | Q235 cold rolled steel sheet |
| Coating | Hot dip galvanized, 275g/m2 average |
| Sheet Thickness | 1.0mm / 1.2mm |
| Band Width | 28mm |
| Profile Height | 8mm |
| Working Diameter | 80mm to 600mm, continuous adjustment |
| Seal Ring | UV stabilised EPDM, black or red |
| Coating Finish | Bright zinc, free from bare cut edges |
| Working Temperature | -20 C to +100 C at the seal |
| Standard | Dimensional check to our drawing on every batch |
| Packing | Carton with shock insert, pallet or wooden case |
We recommend hot dip galvanized clamps whenever the duct is outside the building envelope or in an unheated space where condensation forms on the duct skin. Where the clamp sits in a coastal atmosphere, we can supply the same profile in 304 or 316 stainless instead of galvanized steel, which is often cheaper over the life of the plant than replacing rusted fittings. For projects with a documented coating requirement, we issue the coating mass result with the batch paperwork so the galvanizing can be checked on site without sending a part to a laboratory.
For a coastal project the sensible comparison is a hot dip galvanized duct clamp against a stainless body, and we will quote both so the whole life cost can be judged. Every 275g zinc coating clamp batch is weighed and the coating mass recorded, and that result travels with the outdoor duct coupling clamp shipment.
A: Life depends on the atmosphere. In a rural or city environment a 275g/m2 coating normally gives many years of service; near the coast or in a chemical plant we recommend stainless instead. Tell us the site location and we will advise honestly rather than oversell the galvanized version.
A: Yes, within the stated diameter range. The band compresses the hose onto the duct spigot and the EPDM seal closes the gap. For soft flexible hose we suggest the wider 28mm band, which spreads the load and avoids crushing the hose wall.
A: The seal ring is a separate part captured by the rolled channel and can be swapped in a few minutes with the clamp off the duct. Spare seal rings are available in red or black EPDM and can be packed with each carton.
A: Standard sizes ship in 7 to 15 working days after deposit, and mixed size cartons are normal for this clamp. Give us the size split and the destination port and we will confirm the packing plan and the loading date.
A: Galvanizing after pressing covers the cut edges and the channel interior, which is where paint fails first. That is the practical difference between our outdoor duct coupling clamp and a painted clamp, and the reason a 275g zinc coating clamp is specified on plant that stays outside all year.
Tell us where the duct run is installed and the diameters you need, and we will confirm coating, seal compound and packing for your outdoor ventilation project.
Contact Person: Amy
Tel: 18931182030
Fax: 86-311-85329078