|
Product Details:
|
| Material: | Galvanized Steel / Stainless 304 Option | Thickness: | 1.0mm-1.2mm |
|---|---|---|---|
| Band Width: | 28mm | Diameter Range: | 80mm-600mm |
| Locking Type: | Toggle Lever, Over-centre | Operation: | Manual, Tool Free |
| Seal: | Red TPE | Application: | Spiral Duct Assembly, Temporary Ventilation |
| Highlight: | Toggle lever duct clamp,Tool free duct clamp,One hand duct locking clamp |
||
Labour is the largest cost in a duct installation, and most of that labour is spent at the joints. This toggle lever duct clamp is built for speed: the fitter brings the two duct ends together, drops the band over them and presses the lever down until it goes over centre. There is no spanner, no bolt to lose on a ladder and no torque setting to remember, so a spiral duct run can be assembled by one person working alone.
The lever action also makes the joint repeatable. Once the clamp is set for a diameter, every closure produces the same compression on the seal, which is why the same clamp is used both for permanent ductwork and for temporary or movable duct runs that are stripped and rebuilt. The band is pressed from 1.0mm to 1.2mm steel and covers diameters from 80mm to 600mm without a separate tool for each size.
Contractors comparing a toggle lever duct clamp with a bolted flange usually find the saving is in labour rather than in the part itself. A tool-free duct clamp removes the wrench from the sequence, and a one-hand duct locking clamp lets a single fitter hold the duct and close the joint at the same time — exactly what happens on a ladder or a scissor lift.
| Product Type | Toggle lever duct clamp, over-centre action |
|---|---|
| Operation | One hand, no tools required |
| Body Material | Galvanized steel, stainless 304 on request |
| Thickness | 1.0mm / 1.2mm |
| Band Width | 28mm |
| Working Diameter | 80mm to 600mm, continuous adjustment |
| Lever | Pressed steel lever with finger clearance |
| Seal | Red TPE ring in rolled channel |
| Close Time | Under ten seconds per joint for a trained fitter |
| Reusability | Profile returns to shape after repeated opening |
| Gloves | Lever operable while wearing work gloves |
| Packing | Carton, mixed sizes per carton accepted |
The clamp reaches its best performance when the duct ends are cut square and the spiral seam is deburred; a ragged end will make the lever feel heavy and the joint will leak. We supply a short installation note with each carton for new crews. Contractors who hire out duct and equipment usually order the clamp with a stainless band, since it survives being dropped, stacked and stored outdoors between jobs far better than a painted clamp.
Hire fleets normally specify a toggle lever duct clamp with a stainless band, because a tool-free duct clamp stored outdoors between jobs has to survive being stacked and dropped. Where the same one-hand duct locking clamp is used on duct that is opened weekly, keep a spare seal ring with it.
Q: Will the lever stay locked when the duct vibrates?
A: Yes. The lever closes past the centre point of the linkage, so vibration pushes it further into the locked position rather than releasing it. The same over-centre principle is used on tension latches in machinery.
Q: Can the clamp be used with gloves on?
A: The lever has clearance for a work glove and the pressing force is modest at the sizes normally installed by hand. For the largest 500mm to 600mm sizes the lever is longer, which keeps the effort comfortable.
Q: Is a stainless version available for hire fleets?
A: Yes, the same profile is pressed in 304 stainless for equipment that is stored outside or hired between sites. Tell us the fleet size and we will quote a mixed band and seal package.
Q: How fast is a toggle lever duct clamp to install compared with a bolted clamp?
A: In practice a tool-free duct clamp closes in seconds with no tool change, and the one-hand duct locking clamp is closed while the fitter already has the duct supported. That is where the site labour saving comes from.
Tell us your duct diameters and how often the run is dismantled, and we will recommend the band material and lever size for your installation team.
Contact Person: Amy
Tel: 18931182030
Fax: 86-311-85329078